Broken built-in flash
Hello,is there any simple way to fix bulit-in flash?I have accidentally set mbr-type to msdos on this flash, not on usb-flash, which I wanted to. Now the device is not responding. Nothing. Just...
View ArticleProblem with routing between subnets
Hi, I just wanted to set up my ER-X. Except one thing everything is working fine. I can't access my local network when connected to my vpn. The vpn is provided via openvpn that is running on a...
View ArticleEdge router max block all MAC ID and allow some MAC ID for the router via GUI
Need Help on configuration via GUI aswell CLI am very new to routers Would say Newbie I have configured Edge router for public static IP on ISP 1 eth0 and eth1,eth2 seprate lans 192.168.1.x and...
View ArticleDHCPv6-PD with multiple prefix-id on single interface
Is it possible to configure a single interface (say switch0.8) so that it operates on two IPv6 subnets at the same time while using PD? If I try to add another prefix-id, it just overwrites the...
View ArticleRouter cascade
I'm working on a setup which will allow me to connect a few networks together to include remote operations over airMax devices. Here's what I have so far, and have everything working: ER-X >>...
View ArticleIntermittant SSH and RDP through Edge router infinity.
I have an edge router infitity thats got ports forwarded to allow me to use xrdp and ssh to acces a debian server on my network, only randomly when the server attatches to the network will it let me...
View ArticlePure inet6-unicast BGP peering
Greetings, I generally do my BGP peerings with one per address family. Hence for a given link, I generally have a v4 and a v6 peering (the whole control plane should match the forwarding plane...
View ArticleClik here to view.
Firmware ver. 1 vs ver 2
Hello. I apologize for the stupid question, but there is no possibility.What is the difference between software v1 and v2?Is v1 to LTS - I understand that very stable software with long support time,...
View ArticleClik here to view.
EdgeRouter Lite dead?
Hi, after some time in storage I tried to power on my old EdgeRouter Lite again, but it did not come up. The first odd thing I noticed was that all the green leds are on: So the next thing I checked...
View ArticleUbiquiti Router to replace PFSense
Hi, I currently run a PFSense router on a dedicated server in a datacenter. I am looking to switch to Ubiquiti but have some questions. - Does Ubiquiti have a link to the UI demo for the router? I...
View ArticleNetflix via NordVPN from ER-4
Hello, This has probably been asked a million times before so feel free to direct me to the relevant community page. I'm running a GL.iNet travel router that creates an OpenVPN tunnel to the US in...
View ArticleClik here to view.
ErX traffic analysis not showing all traffic
Hi I have a ErX upgraded to 2.0.3 and it runs fine with hardwarew offloading enabled but the traffic analysis seems to not be showing all traffic. I have attached a screenshot of the traffic analysis...
View ArticleEdgeOS and sFlow with PRTG
I have an ER-4 and I am experimenting with exporting sFlow data to PRTG to try and get some historical logging going on - to cover off those times when people will say "the Internet has been slow at...
View ArticleClik here to view.
Selective routing w/ Parallel Firewall Appliance
The community has saved my butt many times. Thank you! I am very much a networking novice, and my setup has been simple. But my life just got more complicated due to a service we needed at the...
View ArticleReplace failed USB-stick
Sorry but... I have a problem finding information about how to replace a failed USB-memory on a Erl3... I know it's out there somewhere but...Any hints would be appreciated!
View ArticleER-X 80.1q trunking
Hello all, I've spent a few days in this forum and the Internet at large, trying to get the ER-X to pass tagged VLANs to my other switches, but I am now at the end of my wits. I will be forever...
View ArticleDisregard - RTFM in effect
No documentation in the box. No excuses. I should have downloaded one. RTFM!
View ArticleIPv6 mss-clamp6 setting optimization
I just discovered a slew of IPv6 issues I've been having is due to fragmentation. Adjusting my mss-clamp6 setting to 1300 per here:...
View ArticleEdgeRouter 4 port forwarding fails on 2.0.3 firmware
I used the Basic Wizard to setup a simple NAT home network with one port forwarding rule for ssh to an internal address. See the example image the port forwarding page. I'm unable to ssh in from...
View ArticleEdgeRouter PoE eth0 not present after upgrade V2.0.3
EdgeRouter PoE very stable with v1.10.7. Upgrading to release version v2.0.3 and the eth0 port is no longer visable through the gui. I had to perform a Reset to Default, eth0 is present, reloaded my...
View Article