Edgemax 2-site mpls config
Greetings Can anyone help with an MPLS configuration between 2 Edgemax routers: Here is the layout:vlan 2 - SWITCH1vlan 3 - SWITCH1 - trunk - Edgemax1 - (10.1.1.1/29) - vvvlan 5 - SWITCH1 vlan 2 -...
View ArticleHA Edgerouter Pro
Hi:Is there anyway that we can setup a High Availability(HA) using this router. For example, we connect Server A to port 3 and Server B to port 4. Traffic is done on NAT (public IP mapped to a...
View ArticleER Lite Static to AV devices
Have an ER Lite & EdgeSwitch Lite 48, primarily for the reliablity as it's installed as a hub for a new AV residential house. I got sucked into it by my Electrician to help him out, but finding...
View ArticleERL Port Forwarding Wizard Help Please
Hi new here first post have been playing witht eh router for the last 2 weeks pretty impressed. i have setup up internet and modem access and wol on the router with ease but this port forwarding thing...
View ArticleER3 Lite blocking VPN connections
Hi, I was wondering if someone got working an ER3 to allow VPN L2TP/IPsec connections. My setup is pretty simple, I have a remote VPN server working fine for weeks (I can log in at work, school etc.)...
View ArticleEdgerouter PoE - Will this work?
Looking to setup wireless access for some pipeline workers camping outside of a business. Currently have the following setup inside the main building: Cable Modem -> Archer C2 -> 2 Computers +...
View ArticleClik here to view.
Century Link PPPOE Dropped Connections
Hello, Okay, I have a problem with my Century Link DSL connection. It works but it seems a few times a day the connection drops on the PPPOE and then re copnnects in about 2 minutes. Its annoying that...
View ArticleERL to ERL site to site VPN
I have an IPSec VPN set up between two ERLs, A and B. A is the headquarters site, B is a branch office. How do I ensure that all Internet traffic from B goes via site A before routing out the the...
View ArticleStruggling with WAN speed and OpenVPN Server
Hi everyone, got an ERL-3, flashed latest 1.8 firmware. I've been reading a lot but am not able to figure out what the problem is. I have 150/10mbps service from Comcast, when I'm directly connected to...
View ArticleRemote desktop set up public ip
I'm trying to set up a remote desktop to a public ip address in my office. We have two edgerouters router one wan port is eth0 the lan port going to the other router is eth2. I this router we have a...
View Articleblack listed ip - packet capture
So I have a large network for a wisp and I have customers using nat out to the internet but one of the nat addresses has been blick listed and I need to packet capture to find exactly where it's...
View ArticleNoob Question RE edgerouter PRO setup
what i am looking to accomplish is quite simple (not for me however...) i have an edge router pro and what i would like is to have a very basic setup: eth0 would be my WAN and ports eth1 through eth 7...
View ArticleCanal Digital Norway IPv6, Router get but not clients
Hey. I've tried time, and time again to make my edgemax IPv6 ready without luck, I've followed all the guides and after resets, and reboots my best result is always only that the router get IPv6 and...
View ArticleClik here to view.
Slow routing performance between two EdgeRouter PoE
hello, I am kind of irritated by the routing performance between two LANs connected via two EdgeRouter PoEs. The thoughput I have measured with iperf is only about 268 Mbits/sec. here is the setup:...
View ArticleStop Port Scanners
Noticed I've been getting port scanned. Any recommendation to stop this. I have numerous port fowarding setting for various applications so I assume they are hitting those ports; especially those...
View ArticleERL IPSec tunnel to Azure - Only one machine on subnet can ping
So I have the following config: [ERL] -- [Cable Modem] -- [Internet] -- [Azure] Local Subnet: 172.16.1.0/24Azure Subnet: 172.17.0.0/16 - Gateway Subnet: 172.17.0.0/24 - Server Subnet:...
View ArticleEdgeRouter Load Balancing Causes Trouble for VLANs
Hello,I'm running 1.8 with the Load Balance wizard, using WAN 2 as Failover. I have two VLANs, (switch0.2 and switch0.5), and I'm running it straight out of the wizard (Load Balance) with the exception...
View Articlenew edgerouter pro, port 49152 open
Team, Testing a new edgerouter pro. After using the wan+lan2 wizard, I'm seeing that port 49152 is still showing as open in port scans. A buddy of mine stumbled on to...
View Articleiperf3 More Recent Version?
I see ERL 1.7 has iperf3 v. 3.0.1 Is there a way to get the latest version of iperf3 loaded?
View ArticleClik here to view.
Turn Off Firewall (Delete Firewall?)
I am attempting to disable the firewall on our EdgeMax running v1.8.0 since we do not need it, and I cannot figure out how to do this. I attempted creating Firewall Policies that accpeted all packets...
View Article