Setting up VPN
I'm trying to set up VPN on my EdgeRouter Lite. I did the steps in Wille Howe's video: https://www.youtube.com/watch?v=q-64ep6VYS8but of course it isn't working. Is there a file I can show here for...
View ArticleEdgeRouter Lite v1.9.0 - Firewall Logs
Hello guys I have a fairly basic setup with the EdgeRouter Lite. I am using this box with primarily one port forward rule - to open RDP to the internet. I'm checking the Windows Event Viewer and I am...
View ArticleHow do I route between VLANs?
I am setting up a network for a small non-profit and have some noob questions. Equipment (all on latest firmware):o ERLITE-3 routero ES-24-LITE switcho Unifi UAP-AC-PRO-US Configuration is similar to...
View ArticleDNS setting on POE - Newbie question
Hi all - stupid question from a Newbie to Edge OS:Do i need to enter address to the DNS server?I have basically just used the basic wizard and enabled the firewall to get going. Should I use the DNS...
View ArticleERX-SFP Build-in bandwith test - What is normal?
Hi, a simple question about the bandwith test in EdgeOS 1.9.0I have two ERX-SFP connected via single-mode fiber on eth5 with 1,25 Gbps SFP's. In both routers eth5 is member of switch0. When I use the...
View ArticleEdgerouter pro DPI not showing as much detail after 1.9.0
So, I updated to 1.9 a while back, and I'm coming to realize that the Deep Packet Inspection is not showing me the level of information it used to. Before, Youtube, for example, showed up as it's own...
View ArticleWAN Passthrough
We place ERx routers at most of our customer sites to handle our VoIP network, QoS, etc. Sometimes the customer will already have a router in place and needs us to pass a WAN connection to their...
View Article1.7 to 1.9 ipsec down
Cannot figure out why the tunnel is not coming up. Everything was working until I upgraded from 1.7 to 1.9. Waiting on logs from peer side. See anything wrong with my config? ubnt@ubnt-site87:~$ show...
View ArticleSite-To-Site IPSec VPN tcp connection latency
I have two ERX in two sites using a VTI IPSec site-to-site VPN. The VPN works well, pinging between computers on opposite sites are fine too (consistently ~40-50ms). But if I use SSH over the the...
View ArticleClik here to view.
L2TP IPSEC routing woes...
Battled this for days testing and searching. Looking for a fresh set of eyes on the problem. (attaching image for visual clarity.) EdgeMax 5 PoE (running 1.9) on the edge. Downstream I have a Cisco...
View ArticleClik here to view.
Help Configuring Edgerouter POE
Hi all. Long story short, i have set up an Asus access point that has its own IP address, that will be used to serve a guest network to wifi clients. The AP is connected to the ER via the switch and i...
View ArticleClik here to view.
Slow Internet on ERL vs. Directly Wired to Modem (config attached)
Hi All, Finally decided to upgrade from a consumer Linksys Router to a ERL. I followed the most basic guide of WAN+2LAN. My cable modem (CM3016, ISP Comcast) is in bridged mode, connected to eth0. My...
View ArticleCan use some help with site to site VPN
Equipment: 2x EdgeRouter Prov1.9.0 Hi all I'm running currently the vpn between the ERP's with open-vpn all fairness its working but out of the 40mbit upload i must be happy if i can reach 12 to 14...
View ArticleMac address filtering
I have a Ubiquiti wi-fi setup with unifi RL AP and an Edge router lite.I am trying to only allow certain mac address Internet access.Please help a newbie. How do I go about it?
View ArticleSetting up IPv6 access on EdgeRouter Lite
Hi all, IPv6 newbie here! Since my ISP supports IPv6, I thought I'd try and get that working. However, the terminology they're using is a bit different to what I've seen in blog posts around the...
View ArticleIPSEC Site-to-Site VPN Troubleshooting - HELP reqest -> How to Debug
Hi, I have a 'fun' question I have been banging my head against this problem for the last few days, and now I realize I really need to ask forum for brief pointer. - I have a client site with 2 x...
View ArticleNAT'ing and IP - help needed
Wonder if you guys can help. I have configured a site to site vpn (tunnel works and is connected). However I am told that the other end will only accept traffic originating from 10.2.1.8/29.Our local...
View ArticleDDNS and Hairpin NAT
First, the DNS update works perfectly. For some reason, Comcast has begun to periodicaly re-assign new DHCP addresses. It used to be unless I was down for more than eight (8) hours, I have kept some...
View ArticleLoad balancing 1 wan just for upload
Hi, Would it be possible to have wan1 for download and wan2 for upload?
View ArticleRouter-on-a-Stick with multiple uplinks?
Right now I have single port uplink between my core switch and my ER-Pro 8. Since LACP/LAG is terriable on the EdgeRouter due to lack of switched ports, I'm thinking about splitting my vlans between...
View Article