IPSEC Tunnel up, cannot reach devices behind ER-X
Hi, I am quit new to this. But I am trying to establisch an IPSEC tunnel between a Mikrotik and ER-X. Situation is as follow:Mikrotik:WAN: 94.208.*.*Local: 192.168.88.0/24 ER-XWAN: 94.215.*.*Local:...
View ArticlePowering EdgePoint R6
Can you power an EdgePoint R6 with a RocketM2 Titanium power supply?
View Articleedgerouter xg, sfp+ eta?
a german reseller told that there is something around. any eta on that?
View ArticleISP only gave you a /64 and no PD? npd6 on the ER to the rescue
Hello, TLDR; I found a need for npd6 on the EdgeRouter, so i cross compiled it for mips and am now posting it here so people can install it on their own ERLites/ERPoEs if they need it. Would be nice if...
View ArticlePackets are not HW offloaded and I don't get why :/
HI All I've got an EdgeRouter Lite-3, configure with some VLANS,firewall rules and traffic policies.I've noticed that even though HW offload is enabled, packets in any of the VLAN's are not offloaded....
View ArticleSite-to-site IPSec broke when upgrading to 1.9
Hi, I see many threads about this, but mostly all of them seem to mention "load balancing", which I am not using.So i'm creating a new thread since it doesn't seem to fit with my issue.I have tried...
View ArticleInternal To Internet Outbound Traffic Allowed Without A Rule: Why?
Thanks in advance for your help! My Env:- ERPOE-5- 1.9.0- Configured using Wizard for WAN-2LAN-2 (I think... eth1 is bridged). My configuration is below for reference (IPs obfuscated in places...). My...
View ArticleClik here to view.
Help with home network
Hi, I want to buy a ERL and a wifi AP to completely change the homenetwork gear I have at home currently. Before going ahead I´d like to ask if what I plan can be setup properly with the gear I have in...
View ArticleWizard to enable POE
I was wondering when ubiquiti will release a wizard or firmware that supports configuring the erx, ep r6 in router or switch mode and enable POE output on the required ports....
View ArticleL2TP and IPSec with EdgeOS 1.9.0
I am setting up a new L2TP/IPSec VPN on my ERX SFP running 1.9.0, and it doesn't seem to be pushing a default route to clients. When I connect using my laptop, for example, my laptop gets an IP in the...
View ArticleInitial setup connection question
Hello all. I don't understand the Edge OS connecton. quick start says to set my host to static IP, and connect to eth 0. i did, that wokrs, got to the UI. then it says connect my internet to eth 0 and...
View ArticleHigh responce time every 10 seconds
Hi I've setup my EdgeRouter PoE two months ago, over all it's running smoothly, expect one issue. When I try to ping any device behind the EdgeRouter or the EdgeRouter itself, I get a high responce...
View Article2 WANs using PPPoE on same eth interface
Hi, My first question I'm using an Ubuiquiti EdgeMax Lite (3 eth ports) and I would like to ask you if there is possible this type of topology: eth0 - no ip addresspppoe0 - is using eth0 (ip...
View Articleadd a route for the cable modem web interface interface
I have an Arris 6190 on ETH0. The default address for the arris is 192.168.100.1. ETH0 is setup to as DHCP, so it can get its address from my provider (Comcast). I want/need to access the Web UI for...
View ArticleDoes the ER-X's PoE watchdog ping out the specific interface?
Does the ER-X's (SFP or not) PoE watchdog ping out the specific interface that it's configured on or on the entire subnet that it has access to?
View ArticlePower DSL modem with ER-X PoE?
Does anyone have experience with down converting the ER-X's 24v PoE for a 12v DSL modem? I was thinking of using a simple passive PoE midspan with a DC-DC buck converter.
View ArticleHow to view all connected devices (including static) and connected VPN...
Dear all, I have just purchased an ERL and to be honest I am a bit disappointed with its Web GUI. While I knew it is an "enterprise-grade" router and things can be set with CPI, I did expect the GUI...
View ArticleRename portgroup
Is it possible to rename a portgroup/network group through the cli or do I have to create it again?
View ArticleMaintaining access to the DrayTek Vigor 130 web interface when using an...
I have see this come up a few times, so I figured I would do my bit and have the how-to in one place so people can refer to it. The DrayTek Vigor 130 is a commonly used VDSL modem, and has a web UI to...
View Article1000Base-BX-U SFP
I'm looking into connecting an ER directly to the fiber connection coming into my home. The fiber connection is a simplex SC connection. I'll be using a SC>LC cable for conversion to the SFP. Has...
View Article