I have a new ERL, upgraded to v1.9.0 and used the Basic Setup Wizard to attempt to configure as PPPoE router for my ISP (Andrews & Arnold / AAISP in the UK) that delegates a /64 block of IPv6s.
Unfortunately, this doesn't seem to be working correctly. On the Dashboard, the PPPoE connection is showing as Disconnected when I do have a network connection over the PPPoE link. Could this be indicative of a bigger problem?
Also, and no IPv6 has been allocated to my system.
Below is my config, and comparing ths with some of the guides / other IPv6 configs, I can see that some of the prefix delegation commands seem to be missing but I would welcome your feedback on what the problem could be.
Please see my config below.
firewall {
all-ping enable
broadcast-ping disable
ipv6-name WANv6_IN {
default-action drop
description "WAN inbound traffic forwarded to LAN"
enable-default-log
rule 10 {
action accept
description "Allow established/related sessions"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
}
ipv6-name WANv6_LOCAL {
default-action drop
description "WAN inbound traffic to the router"
enable-default-log
rule 10 {
action accept
description "Allow established/related sessions"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
rule 30 {
action accept
description "Allow IPv6 icmp"
protocol ipv6-icmp
}
rule 40 {
action accept
description "allow dhcpv6"
destination {
port 546
}
protocol udp
source {
port 547
}
}
}
ipv6-receive-redirects disable
ipv6-src-route disable
ip-src-route disable
log-martians enable
name WAN_IN {
default-action drop
description "WAN to internal"
rule 10 {
action accept
description "Allow established/related"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
}
name WAN_LOCAL {
default-action drop
description "WAN to router"
rule 10 {
action accept
description "Allow established/related"
state {
established enable
related enable
}
}
rule 20 {
action drop
description "Drop invalid state"
state {
invalid enable
}
}
}
options {
mss-clamp {
mss 1412
}
}
receive-redirects disable
send-redirects enable
source-validation disable
syn-cookies enable
}
interfaces {
ethernet eth0 {
description "Internet (PPPoE)"
duplex auto
mtu 1508
pppoe 0 {
default-route auto
firewall {
in {
ipv6-name WANv6_IN
name WAN_IN
}
local {
ipv6-name WANv6_LOCAL
name WAN_LOCAL
}
}
mtu 1500
name-server auto
password ****************
user-id ********
}
speed auto
}
ethernet eth1 {
address 10.0.0.1/24
description Local
duplex auto
speed auto
}
ethernet eth2 {
address 10.10.0.1/24
description "Local 2"
duplex auto
speed auto
}
loopback lo {
}
}
service {
dhcp-server {
disabled false
hostfile-update disable
shared-network-name LAN1 {
authoritative enable
subnet 10.0.0.0/24 {
default-router 10.0.0.1
dns-server 10.0.0.1
lease 86400
start 10.0.0.38 {
stop 10.0.0.243
}
}
}
shared-network-name LAN2 {
authoritative enable
subnet 10.10.0.0/24 {
default-router 10.10.0.1
dns-server 10.10.0.1
lease 86400
start 10.10.0.38 {
stop 10.10.0.243
}
}
}
use-dnsmasq disable
}
dns {
forwarding {
cache-size 150
listen-on eth1
listen-on eth2
}
}
gui {
http-port 80
https-port 443
older-ciphers enable
}
nat {
rule 5010 {
description "masquerade for WAN"
outbound-interface pppoe0
type masquerade
}
}
ssh {
port 22
protocol-version v2
}
}
system {
domain-name mydomain.org
host-name ubnt
login {
user ** {
authentication {
encrypted-password ****************
}
level admin
}
}
ntp {
server 0.ubnt.pool.ntp.org {
}
server 1.ubnt.pool.ntp.org {
}
server 2.ubnt.pool.ntp.org {
}
server 3.ubnt.pool.ntp.org {
}
}
offload {
hwnat disable
ipv4 {
forwarding enable
pppoe enable
}
}
syslog {
global {
facility all {
level notice
}
facility protocols {
level debug
}
}
}
time-zone Europe/London
traffic-analysis {
dpi enable
export enable
}
}Thanks in advance,
Matt